Quality of Service in Tungsten Fabric

date

2020-04-03

Overview: Quality of Service

Quality of service (QoS) in networking provides the ability to control reliability, bandwidth, latency, and other traffic management features. Network traffic can be marked with QoS bits (DSCP, 802.1p, and MPLS EXP) that intermediate network switches and routers can use to provide service guarantees.

TF QoS Model

The QoS model in Tungsten Fabric has the following features:

  • All packet forwarding devices, such as vRouter and the gateway, combine to form a system.

  • Interfaces to the system are the ports from which the system sends and receives packets, such as tap interfaces and physical ports.

  • Fabric interfaces are where the overlay traffic is tunneled.

  • QoS is applied at the ingress to the system, for example, upon traffic from the interfaces to the fabric.

  • At egress, packets are stripped of their tunnel headers and sent to interface queues, based on the forwarding class. No marking from the outer packet to the inner packet is considered at this time.

Features of Fabric Interfaces

Fabric interfaces, unlike other interfaces, are always shared. Therefore, fabric interfaces are common property. Consequently, traffic classes and QoS marking on the fabric must be controlled by the system administrator. The administrator might choose to provision different classes of service on the fabric.

In TF, classes of service are determined by both of the following:

  • Queueing on the fabric interface, including queues, scheduling of queues, and drop policies, and

  • forwarding class, a method of marking that controls how packets are sent to the fabric, including marking and identifying which queue to use.

Tenants can define which forwarding class their traffic can use, deciding which packets use which forwarding class. The TF QoS configuration object has a mapping table, mapping the incoming DSCP or 802.1p value to the forwarding class mapping.

The QoS configuration can also be applied to a virtual network, an interface, or a network policy.

QoS Configuration Parameters for Provisioning

Configuring QoS in Tungsten Fabric Release 5.0 and Later

This section describes how to provision QoS in Tungsten Fabric release 5.0 and later.

  1. Define the hardware queues and priority group in the instances.yaml file under the vrouter role as shown below.

    nodeh5:
        ip: 10.xxx.xxx.109
        provider: bms
        roles:
          vrouter:
            VROUTER_GATEWAY: 192.168.1.45
            PRIORITY_ID: 0,1,2,3,4,5,6,7
            PRIORITY_BANDWIDTH: 0,10,0,20,0,30,0,40
            PRIORITY_SCHEDULING: strict,rr,strict,rr,strict,rr,strict,rr
            QOS_QUEUE_ID: 3,11,18,28,36,43,61,53
            QOS_LOGICAL_QUEUES: "[ 1, 6-10, 12-15];[40-46];[70-74, 75, 80-95];[115];[140-143, 145];[175];[245];[215]"
            QOS_DEF_HW_QUEUE: True
          openstack_compute:
    
  2. In the already provisioned setup, define the QoS configuration in the /etc/contrail/common_vrouter.env file as shown in the following sample.

    PRIORITY_ID=0,1,2,3,4,5,6,7
    PRIORITY_BANDWIDTH=0,10,0,20,0,30,0,40
    PRIORITY_SCHEDULING=strict,rr,strict,rr,strict,rr,strict,rr
    QOS_QUEUE_ID=3,11,18,28,36,43,61,53
    QOS_LOGICAL_QUEUES="[ 1, 6-10, 12-15];[40-46];[70-74, 75, 80-95];[115];[140-143, 145];[175];[245];[215]"
    QOS_DEF_HW_QUEUE=True
    
  3. Execute the execute docker-compose up -d under /etc/contrail/vrouter/ command.

Queuing Implementation

The vRouter provides the infrastructure to use queues supplied by the network interface, a method that is also called hardware queueing. Network interface cards (NICs) that implement hardware queueing have their own set of scheduling algorithms associated with the queues. The TF implementation is designed to work with most NICs, however, the method is tested only on an Intel-based 10G NIC, also called Niantic.

TF QoS Configuration Objects

TF QoS configuration objects include the:

  • forwarding class

  • QoS configuration object (qos-config)

The forwarding class object specifies parameters for marking and queuing, including:

  • The DSCP, 802.1p, and MPLS EXP values to be written on packets.

  • The queue index to be used for the packet.

The QoS configuration object specifies a mapping from DSCP, 802.1p, and MPLS EXP values to the corresponding forwarding class.

The QoS configuration has an option to specify the default forwarding class ID to use to select the forwarding class for all unspecified DSCP, 802.1p, and MPLS EXP values.

If the default forwarding class ID is not specified by the user, it defaults to the forwarding class with ID 0.

Processing of QoS marked packets to look up the corresponding forwarding class to be applied works as follows:

  • For an IP packet, the DSCP map is used .

  • For a Layer 2 packet, the 802.1p map is used.

  • For an MPLS-tunneled packet with MPLS EXP values specified, the EXP bit value is used with the MPLS EXP map.

  • If the QoS configuration is untrusted, only the default forwarding class is specified, and all incoming values of the DSCP, 802.1p, and EXP bits in the packet are mapped to the same default forwarding class.

Figure 1 shows the processing of QoS packets.

Figure 1: Processing of QoS Packets

A virtual machine interface, virtual network, and network policy can refer to the QoS configuration object. The QoS configuration object can be specified on the vhost so that underlay traffic can also be subjected to marking and queuing.

Figure 2: Referring to the QoS Object

Example: Mapping Traffic to Forwarding Classes

This example shows how traffic forwarding classes are defined and how the QoS configuration object is defined to map the QoS bits to forwarding classes.

Table 1 shows two forwarding class objects defined. FC1 marks the traffic with high priority values and queues it to Queue 0. FC2 marks the traffic as best effort and queues the traffic to Queue 1.

Table 1: Forwarding Class Mapping

Name

ID

DSCP

802.1p

MPLS EXP

Queue

FC1

1

10

7

7

0

FC2

2

38

0

0

1

In Table 2, the QoS configuration object DSCP values of 10, 18, and 26 are mapped to a forwarding class with ID 1, which is forwarding class FC1. All other IP packets are mapped to the forwarding class with ID 2, which is FC2. All traffic with an 802.1p value of 6 or 7 are mapped to forwarding class FC1, and the remaining traffic is mapped to FC2.

Table 2: QoS Configuration Object Mapping

DSCP

F orwarding Class ID

802.1p

F orwarding Class ID

MPLS EXP

F orwarding Class ID

10

1

6

1

5

1

18

1

7

1

7

1

26

1

*

2

*

1

*

2

QoS Configuration Object Marking on the Packet

The following sections describes how QoS configuration object marking is handled in various circumstances.

Traffic Originated by a Virtual Machine Interface

  • If a VM interface sends an IP packet to another VM in a remote compute node, the DSCP value in the IP header is used to look into the qos-config table, and the tunnel header is marked with DSCP, 802.1p, and MPLS EXP bits as specified by the forwarding class.

  • If a VM sends a Layer 2 non-IP packet with an 802.1p value, the 802.1p value is used to look into the qos-config table, and the corresponding forwarding class DSCP, 802.1p, and MPLS EXP value is written to the tunnel header.

  • If a VM sends an IP packet to a VM in same compute node, the packet headers are not changed while forwarding. The original packet remains unchanged.

Traffic Destined to a Virtual Machine Interface

For traffic destined to a VMI, if a tunneled packet is received, the tunnel headers are stripped off and the packet is sent to the interface. No marking is done from the outer packet to inner packet.

Traffic from a vhost Interface

The QoS configuration can be applied on IP traffic coming from a vhost interface. The DSCP value in the packet is used to look into the qos-config object specified on the vhost, and the corresponding forwarding class DSCP and 802.1p values are overwritten on the packet.

Traffic from fabric interface

The QoS configuration can be applied while receiving the packet on an Ethernet interface of a compute node, and the corresponding forwarding class DSCP and 802.1p values are overwritten on the packet.

QoS Configuration Priority by Level

The QoS configuration can be specified at different levels.

The levels that can be configured with QoS and their order of priority:

  1. in policy

  2. on virtual-network

  3. on virtual-machine-interface

Queuing

Tungsten Fabric supports QoS. These sections provide an overview of the queuing features available in Tungsten Fabric.

The queue to which a packet is sent is specified by the forwarding class.

Queue Selection in Datapath

In vRouter, in the data path, the forwarding class number specifies the actual physical hardware queue to which the packet needs to be sent, not to a logical selection as in other parts of TF. There is a mapping table in the vRouter configuration file, to translate the physical queue number from the logical queue number.

Hardware Queueing in Linux kernel based vRouter

If Xmit-Packet-Steering (XPS) is enabled, the kernel chooses the queue, from those available in a list of queues. If the kernel selects the queue, packets will not be sent to the vRouter-specified queue.

To disable this mapping:

  • have a kernel without CONFIG_XPS option

  • write zeros to the mapping file in /sys/class/net//queues/tx-X/xps_cpus .

When this mapping is disabled, the kernel will send packets to the specific hardware queue.

To verify:

See individual queue statistics in the output of ‘ethtool -S ‘ command.

Parameters for QoS Scheduling Configuration

The following shows sample scheduling configuration for hardware queues on the compute node.

The priority group ID and the corresponding scheduling algorithm and bandwidth to be used by the priority group can be configured.

Possible values for the scheduling algorithm include:

  • strict

  • rr (round-robin)

When round-robin scheduling is used, the percentage of total hardware queue bandwidth that can be used by the priority group is specified in the bandwidth parameter.

The following configuration and provisioning is applicable only for compute nodes running Niantic NICs and running kernel based vrouter.

qos_niantic =  {
       ‘compute1': [
                         { 'priority_id': '1', 'scheduling': 'strict', 'bandwidth': '0'},
                         { 'priority_id': '2', 'scheduling': 'rr', 'bandwidth': '20'},
                         { 'priority_id': '3', 'scheduling': 'rr', 'bandwidth': '10’}
       ],
       ‘compute2' :[
                         { 'priority_id': '1', 'scheduling': 'strict', 'bandwidth': '0'},
                         { 'priority_id': '1', 'scheduling': 'rr', 'bandwidth': '30’}
        ]
}